Got the z table hooked up but nothing happens when I try and jog it from LW4 what should i be looking for on the board and the controller as far as lights go?
Got the z table hooked up but nothing happens when I try and jog it from LW4 what should i be looking for on the board and the controller as far as lights go?
“William Kearns”
Ashley M. Kirchner [Norym] August 07, 2017 05:02
Need more info. What z-table? How is it wired in? Pictures?
William Kearns August 07, 2017 05:15
+Ashley M. Kirchner
William Kearns August 07, 2017 05:16
William Kearns August 07, 2017 05:16
William Kearns August 07, 2017 05:16
William Kearns August 07, 2017 05:17
William Kearns August 07, 2017 05:17
Ashley M. Kirchner [Norym] August 07, 2017 05:22
Looks like you followed my guide. Did you also make the config changes as stated in the guide?
William Kearns August 07, 2017 05:30
yes I copied and pasted them from the guide.
Ashley M. Kirchner [Norym] August 07, 2017 05:34
Ok, just going through checks here. Is the external PSU powered up? Are the green LEDs on the external driver on?
William Kearns August 07, 2017 05:37
it appears to be the light is green on the external PSU and i noticed there is only one light switched on the controller. There are two green ones right next to each other
Ashley M. Kirchner [Norym] August 07, 2017 05:44
Ok, yeah, one is power, the other is an alarm. Ok, can you dump your entire config.txt into a pastebin (pastebin.com) and send me the URL for it?
William Kearns August 07, 2017 05:46
yes will send later on Monday. thank you for looking! closing up shop now
Ashley M. Kirchner [Norym] August 07, 2017 05:52
Cheers!
William Kearns August 08, 2017 02:52
did i do that right?
Ashley M. Kirchner [Norym] August 08, 2017 03:07
Ok, so all of that looks ok at first glance. Next, in LW, did you enable the Z Stage?
William Kearns August 08, 2017 03:08
i keep getting an alarm lock? when i jog the z axis it started to move then stopped?
William Kearns August 08, 2017 03:09
Ashley M. Kirchner [Norym] August 08, 2017 03:14
what happens if you clear the alarm, then jog again?
William Kearns August 08, 2017 03:16
just figured out the clear alarm. The motor turns but just barley @ its jerky put jog at 100mm and it maybe turns a quater of a turn. Is there any other setting i might be missing?
Ashley M. Kirchner [Norym] August 08, 2017 03:26
I need to see what your LW settings are. At 0.1mm it should move just a little bit, but at 100mm it should be spinning fast and smooth.
William Kearns August 08, 2017 03:32
doesnt turn at all just a high pitch hiss almost when the command is sent to it.
William Kearns August 08, 2017 03:35
could it be motor current anyway to adjust that?
Ray Kholodovsky (Cohesion3D) August 08, 2017 03:36
Set the red dip switches of the tb6600 for 1 amp and 1/16 micro stepping. Carefully note which way is on for them.
William Kearns August 08, 2017 03:38
This is how it’s set now
William Kearns August 08, 2017 04:13
Set it to this and it makes a super light squeaking noise and it does not turn.
Imported from Google+ — content and formatting may not be reliable